This flooring underlay buying guide is written for Melbourne owner-installers who have already clicked “buy” on a laminate or hybrid floor and now need to work out what goes underneath. Furthermore, it skips the fluff. Because TFC ships supply-only from a Melbourne clearance warehouse, the advice here is aimed squarely at DIYers in Werribee, Tarneit, Craigieburn, Cranbourne and Pakenham who want to keep the underlay cost proportional to the floor itself. In addition, every product option referenced is a foam, rubber or moisture-barrier type sold for floating floors — acoustic compliance and strata ratings are deliberately out of scope.
What flooring underlay actually does
Underlay sits between the subfloor and a click-lock floating floor. Therefore, it performs three jobs at once. Firstly, it smooths minor subfloor imperfections so the locking joints do not stress. Secondly, it adds a thin layer of thermal and impact cushioning. Thirdly, on a concrete slab, it blocks residual moisture from reaching the laminate core. However, underlay is not a levelling compound. Consequently, a slab or timber subfloor with dips larger than 3 mm over a 2 m span still needs patching before the floor goes down.
The three underlay types DIY floaters need to know
For supply-only buyers, the market narrows to three practical categories. Furthermore, each one maps to a specific subfloor and budget.
- Closed-cell foam (EPE or XPE): the cheapest option. Typically 2 mm thick, rolled, and fine for timber subfloors upstairs or in dry areas.
- Combo foam with moisture barrier: the workhorse for Melbourne slab-on-ground homes. A green film on one side seals residual slab moisture while the foam cushions the plank.
- Rubber crumb or cork-rubber: heavier, denser, and useful where a little extra underfoot softness is wanted. Although more expensive per square metre, it still sits well below designer specialty products.
As a result, most DIY jobs in the Wyndham and Casey growth corridors end up on combo foam with a built-in moisture barrier, because almost every new build there is slab-on-ground.
Thickness: why 2 mm foam is the cheapest workable floor
Laminate and hybrid click-lock manufacturers publish a maximum underlay thickness for warranty purposes. Overall, 2 mm is the sweet spot. Because thicker foam flexes too much under the joint, it can cause click-lock boards to separate over time. However, thinner than 1.5 mm and the floor starts to telegraph every subfloor pebble. Therefore, a 2 mm closed-cell foam is the default cheap pick for DIYers, and buying it by the roll rather than the piece cuts the per-metre rate noticeably.
Moisture barrier: when a concrete slab demands it
Any floor going directly onto a concrete slab needs a moisture barrier. In addition, the Australian Standard for floating-floor installation treats the vapour layer as mandatory on ground-floor slabs, no matter how old the slab is. Consequently, a DIYer fitting laminate over a 1990s slab in Sunshine or a 2024 slab in Mickleham both need the same thing: a continuous 200-micron film, either built into the underlay or taped down as a separate sheet first. Because TFC stocks combo underlay with the barrier pre-laminated, most owner-installers save an entire step by buying the two-in-one product.
Underlay vs subfloor prep — don’t confuse them
This is the mistake that costs DIYers their warranty. Although underlay softens small bumps, it cannot fix a wavy slab. Therefore, before unrolling anything, run a 2 m straightedge across the subfloor in both directions. If the gap beneath the edge exceeds 3 mm, patch the low spots with a self-levelling compound and let it cure. Furthermore, vacuum the slab thoroughly — grit trapped under the foam is the number-one cause of early click-lock joint failure.
Comparison table: foam vs combo vs rubber underlay
| Type | Typical thickness | Best for | Indicative $/m² | Moisture barrier? |
|---|---|---|---|---|
| Closed-cell foam (EPE/XPE) | 2 mm | Upstairs timber subfloors, dry rooms | $1.50 – $3.00 | No |
| Combo foam + vapour film | 2 mm | Slab-on-ground homes in growth corridors | $2.50 – $4.50 | Yes (built in) |
| Rubber / cork-rubber | 3 mm | Kitchens and living zones needing extra give | $6.00 – $10.00 | Sometimes (check label) |
Prices shown are indicative clearance-tier figures for supply-only stock and exclude delivery. In addition, buying a full roll almost always beats a pack rate.
How to order underlay for a Melbourne growth-corridor home
Measure the room in metres, multiply length by width, then add 7–10 % for trimming waste. Furthermore, round up to the nearest full roll because offcuts are useful at doorways and under joins. Because TFC ships supply-only across metropolitan Melbourne, a DIYer in Point Cook or Clyde North can have underlay, laminate and accessories arrive on the same pallet. As a result, there is no double freight cost to juggle.
When the underlay and floor arrive, store the rolls flat in the room for 48 hours before unrolling. Consequently, both products acclimatise to the same temperature and humidity, which reduces expansion headaches after install.
Ready to buy? Browse the current underlay range on the flooring underlay category, match it to a laminate or hybrid pick from the clearance sale, check your free delivery zone, then head to the shop to place the order.
Frequently Asked Questions
Do I need underlay if my hybrid flooring has a pre-attached pad?
If the plank already carries a bonded EVA or IXPE pad, a separate foam underlay is not required and, in many cases, will void the warranty. However, a slab-on-ground subfloor still needs a standalone vapour barrier, so a 200-micron builder’s film goes down first.
What is the cheapest underlay I can safely use under laminate?
A 2 mm closed-cell EPE foam roll is the cheapest option that still meets most manufacturer warranties. Furthermore, it is suitable for dry, timber-framed upper floors. For a concrete slab, step up to the combo foam with a built-in vapour barrier.
Can I tape two underlay types together for extra cushioning?
No. Stacking underlays almost always exceeds the manufacturer’s maximum thickness and causes click-lock joints to flex and separate. Therefore, choose a single product rated for the subfloor and leave it at that.
How much underlay waste should I order for a growth-corridor home?
Add 7–10 % to the floor area for trimming and overlap. Consequently, a 120 m² single-storey floorplan in Tarneit or Craigieburn usually needs around 128–132 m² of underlay, which lines up to three or four standard rolls.
Does underlay fix a wavy slab?
No. Underlay cushions surface texture, not dips. Although a 2 mm foam can absorb pebble-sized bumps, any slab variation greater than 3 mm over 2 m must be patched with a self-levelling compound before the underlay goes down.

